Audi A1 Rear Bumper: Fitment, Sensors & Common Damage
On the A1, image distortion when turning the steering wheel is genuinely a documented issue on related models, distinct from simple wiring.
Illustration for editorial purposes
Opens live listings in a new tab.
OEM Part Number: confirm via VIN — rear bumper (aftermarket) Prasco AD1221051 / Van Wezel 0304544
| Rear bumper covers (aftermarket) | Prasco AD1221051 (Rear, primed); Prasco AD1221061 (Rear, primed, with holes for park assist); Prasco AD1201051 (Rear, primed, with holes for park assist); Prasco AD1201061 (Rear, primed, with holes for parking sensors); Van Wezel 0304544 (Rear, for vehicles without parking sensors, primed, Smooth, for facelift); Van Wezel 0304545 (Rear, primed, Smooth, with holes for parking sensors, for facelift) |
|---|---|
| Lower sections, corners & trims | None listed separately |
| Genuine (OE) numbers quoted | None quoted in the catalogue listings — the genuine cover varies by body style, parking sensors and tow bar, so order it against your VIN |
| Fitment notes | Match body style, facelift date and the holes for parking sensors or exhaust trims; covers come primed and need painting to your paint code before fitting. |
Audi A1 Rear Bumper: More Than Just a Plastic Panel
It's rarely a plain plastic panel on the Audi A1: the rear bumper usually integrates parking sensors and a reversing camera housing, sometimes exhaust trim too, so a seemingly minor kerb scrape can end up needing more than a simple like-for-like swap.
Audi A1 Rear Bumper: What It Does
Beyond absorbing minor impacts, the rear bumper on higher trims of the A1 often houses parking sensors, a reversing camera, and sometimes integrated exhaust finishers. A bumper that looks compatible can still be missing the correct cutouts or wiring provisions for your specific trim's equipment.
Audi A1 Rear Bumper: Watch: Replacing It
The sequence is much the same on this generation: wheel-arch liner screws, the fixings along the boot aperture and under the lower edge, then unclip each corner from the wing and unplug any sensor loom before the cover comes away.
Audi A1 Rear Bumper: Generations, Derivatives & Colour
| 8X (2010–2018), standard trims | Amalfi White, Ice Silver, Daytona Grey, Brilliant Black |
|---|---|
| GB (2019–present), standard trims | Shell White (no-cost) — genuinely a different shade to the "Ibis White" used elsewhere in the Audi range, which caused some confusion among early buyers; also offered in Manhattan Grey, Tioman Green, Misano Red |
| S line/Vorsprung | Turbo Blue and Chronos Grey are exclusive to S line and above, replacing Firmament Blue and Manhattan Grey; the rear bumper is also styled differently on this trim |
| Black Edition | Comes standard with a two-tone body/roof combination — Shell White is genuinely not available on this trim since it can't be paired with the contrast roof |
Opens live listings in a new tab.
A Genuinely Useful Piece of Context Worth Knowing About Reversing Camera Faults — Audi A1 Rear Bumper
If a retrofitted reversing camera image becomes distorted specifically when the steering wheel is turned, this is genuinely worth knowing: this is a documented issue in its own right on related Audi models, distinct from a simple wiring or power fault.
It's also genuinely worth knowing that some CANbus interface units genuinely can't provide enough current to both switch the head unit into camera mode and power the camera at the same time, and that fitting a towbar to certain performance variants isn't officially advised due to cooling concerns.
Audi A1 Rear Bumper: Common Damage, DIY Difficulty & Aftermarket Advice
These are the same regardless of make or model — see our full Rear Bumper Guide for common damage types, confirming fitment (body style and sensor equipment matter here), and OEM vs aftermarket guidance.
More Audi Rear Bumper
The same part, covered across other Audi models.