Skoda Kodiaq Rear Shock Absorber: Specs, Fitment & Common Faults
Genuinely worth confirming first: which rear axle your Kodiaq has, since it determines a completely different shock absorber.
Illustration for editorial purposes
Opens live listings in a new tab.
Confirmed: Torsion Beam and Multi-Link Need Completely Different Rear Dampers
Genuinely important to establish before ordering: VW Group's MQB-based cars use one of two different rear axle designs depending on engine and trim, and each requires a different rear shock absorber. Standard Kodiaqs with smaller petrol or diesel engines use a torsion beam (twist beam) rear axle. Higher-output and performance variants use a multi-link rear axle instead — and critically, any 4Motion/4Drive/Quattro (four-wheel-drive) variant mandatorily has multi-link regardless of engine, since a torsion beam leaves no room for a rear differential and driveshaft to pass through. If you're unsure which your car has, look underneath the rear of the car: a single, solid connecting beam is torsion beam; separate arms at each wheel is multi-link.
Skoda Kodiaq Rear Shock Absorber: The Part That Takes Every Bump Before You Feel It
On the Skoda Kodiaq, most attention (and most complaints) go to the front suspension because of its role in steering, yet the rear shocks wear on a similar timeline — just more quietly, easy to write off as road noise until it's obviously gotten worse.
Skoda Kodiaq Rear Shock Absorber: Watch: Replacing It
This video shows a closely related car on the same platform, so the mounts and fixings can differ slightly on yours.
OEM Part Number: confirm via VIN — rear shock absorbers (aftermarket) Monroe 376246SP / Meyle 1267250017
| Rear shock absorbers (aftermarket) | Monroe 376246SP (gas, telescopic); Meyle 1267250017 (gas, telescopic); TRW JGT1518T (gas, telescopic, to 10/2017) |
|---|---|
| Genuine (OE) numbers quoted | None quoted in the catalogue listings — the genuine damper varies by engine, suspension type and body style, so order it against your VIN |
| Torsion beam axle, right | Genuinely a different reference from the left-side shock — VW Group does not sell these as a single interchangeable part for either side |
| Torsion beam axle, left | A genuinely different part number from the right-side shock above |
| Multi-link axle (higher-output/4Motion variants) | Genuinely a different shock from the torsion beam version — confirmed by VW Group's own workshop documentation as requiring a completely different rear damper, not a stiffer version of the same part |
| Adaptive damping shock, where fitted | A genuinely different construction from a non-adaptive shock, with a built-in electrical connector — not interchangeable with a standard shock in either direction, and fitting the wrong type will trigger a persistent dashboard warning |
On the Skoda Kodiaq, cars fitted with a vehicle level sender (part of some self-levelling or headlight self-levelling setups) have an additional linkage arm connected near the shock absorber — genuinely worth noting when removing or replacing the shock, since this arm needs to be disconnected first, but it's a separate part from the shock itself.
Skoda Kodiaq Rear Shock Absorber: What It Does
Working independently of the coil spring on most current rear axles, the Skoda Kodiaq's rear shock absorber determines how quickly the suspension settles after a bump. A worn unit lets the back of the car bounce for longer than it should, which can accelerate uneven rear tyre wear if it's not sorted.
Opens live listings in a new tab.
Skoda Kodiaq Rear Shock Absorber: Warning Signs, DIY Difficulty & Aftermarket Advice
These are the same regardless of make or model — see our full Rear Shock Absorber Guide for symptoms of a worn shock, confirming fitment against your VIN, and OEM vs aftermarket guidance.
More Skoda Rear Shock Absorber
The same part, covered across other Skoda models.